XPC slim DS77U3

• Fanless and Silent
  Passive cooling, no fan noise at all
  Perfect to be used in noise-sensitive environments
  Fanless, dust-free and thus virtually maintenance-free
• Low Power Consumption
  Power consumption in idle mode under Windows 10: ca. 7~8 W only
• 24/7 Nonstop Operation
  This device is approved for 24/7 permanent operation.
  Requirements:
  – Free circulation of air amongst the PC must be guaranteed.
  – Ventilation holes must stay clear.
  – If a hard disk is installed, this must also be approved for permanent operation by its manufacturer
• Chassis
  Slim-PC (Nettop) with black chassis made of steel
  Without cooling fan, passive cooling only
  The bays for memory, 2.5″ drive and M.2 card
  can be easily accessed by removing two cover plates.
  Dimensions: 200 x 165 x 39.5 mm (LWH) = 1.3 litres
  Weight: 1.43 kg net and 2.13 kg gross
  Two holes for Kensington Lock and numerous
  threaded holes (M3) at both sides of the chassis
• Operation Position
  1) Vertical: Usually operated in vertical position with the supplied feet (DisplayPort output facing up).
  2) VESA-mounted: The device can also be mounted behind an appropriate monitor using the supplied VESA mount kit.
  Note: From a thermal point of view horizontal operation is permitted, however, there are no rubber feet on the device. The maximum operating temperature is 35 °C then.
• Operation System
  This barebone system comes without operating system.
  It is compatible with Windows 10 (64-bit) and Linux (64-bit).
• Processor
  Model: Intel Core i3-7100U (ULV)
  System-on-a-chip architecture (SoC): no chipset required
  BGA1356 package – directly soldered onto the mainboard
  Code name: Kaby Lake-U (7th Generation Intel Core)
  Cores / Threads: 2 / 4
  Clock rate: 2.4 GHz
  L1/L2/L3 Cache: 128 kB / 512 kB / 3072 kB
  Memory controller: DDR4-2133 Dual Channel (1.2 V)
  TDP wattage: 15 W maximum
  Manufacturing process: 14 nm
  Maximum Tjunction Temperature: 100 °C
  Supports Hyper-Threading (HT), 64-bit, VT-x (EPT), VT-d, Enhanced SpeedStep, NX bit, AES-NI, SSE 4.1/4.2
  Integrated graphics engine
• Integrated Graphics
  Intel HD graphics 620
  GPU clock frequency: 300~1000 MHz
  Execution Units (EUs): 24
  Three digital audio/video ports support three independent screens:
  Supports Ultra HD / 4K resolution at 3840 x 2160 Pixels
  1) DisplayPort 1.2 [2,7] supports Ultra HD @ 60 Hz
  2) 2x HDMI 1.4b supports Ultra HD @ 30 Hz
  Note: the DisplayPort of DS77U3 does not support audio output
• Mainboard / BIOS
  Shuttle Mainboard FS77
  All capacitors are high quality solid capacitors
  Supports resume after power failure [6]
  Supports Wake on LAN (WOL)
  Supports Power on by RTC Alarm
  Supports boot from M.2 SSD cards, USB devices and SD card reader
  AMI BIOS in 8 MByte EEPROM with SPI interface
  Supports hardware monitoring and watch dog function
  Supports Unified Extensible Firmware Interface (UEFI)
• Power Adapter
  External 65 W power adapter (fanless)
  Input: 100~240 V AC, 50/60 Hz, max. 1.6 A
  Output: 19 V DC, max. 3.42 A, max. 65 W
• DC Input connector
  DC Input Connector: 5.5 / 2.5 mm (outer/inner diameter)
  The DC-input of the computer supports an external
  power source with either 12V±5% or 19V±5%.
• Memory support
  2x SO-DIMM slots with 260 pins
  Supports DDR4-2133 (PC4-17000) SDRAM at 1.2 V
  Supports Dual Channel mode
  Supports a maximum of 16 GB per DIMM,
  maximum total size: 32 GB
  Supports two unbuffered DIMM modules (no ECC or registered)
• 2.5″ Drive Bay with SATA connector
  Supports one Serial ATA hard disk
  or one SATA SSD drive in 6.35 cm / 2.5″ format
  Device height: max. 12.5 mm
  Supports Serial-ATA III, 6 Gb/s (600 MB/s) bandwidth
  Supports Unified Extensible Firmware Interface (UEFI)
  Note: no Serial ATA cable is required
• M.2 Slot for SSDs
  The M.2 2280 BM slot provides the following interfaces:
  – PCI-Express Gen. 3.0 X4 with up to 32 Gbps Data Transfer Speed
  – SATA v3.0 (max. 6 Gbps)
  It supports M.2 cards with a width of 22 mm
  and a length of 42, 60 or 80 mm (type 2242, 2260, 2280).
  Supports M.2 SATA SSDs (with B+M key) and M.2 PCIe SSDs (with M key)
• Card Reader
  Integrated SD card reader
  Supports SD, SDHC and SDXC memory flash cards
  Supports booting from SD card
• Audio
  Audio Realtek® ALC 662 High-Definition Audio
  Two analog audio connectors (3.5 mm) at the back panel:
  1) 2 channel line out (headphones)
  2) microphone input
  Digital multi-channel audio output: via HDMI
• Dual Gigabit LAN
  Dual network with two RJ45 ports
  Used network chips:
  1) Intel i211 Ethernet Controller with MAC, PHY and PCIe interface
  2) Intel i219LM PHY connected to the MAC of the processor
  Supports 10 / 100 / 1.000 MBit/s operation
  Supports WAKE ON LAN (WOL)
  Supports network boot by Preboot eXecution Environment (PXE)
  Supports Teaming mode [3]
• Wireless Network (WLAN)
  Built-in M.2-2230-A/E WLAN card and internal antenna
  Single-Chip 1T1R WLAN Controller Realtek RTL8188EE
  Supports IEEE 802.11b/g/n, max. 150 Mbps up-/downstream
  Security: WPA/WPA2(-PSK), WEP 64/128 bit, IEEE 802.11x/i
• Front Panel connectors
  2x USB 3.0
  2x USB 2.0
  2x RS232 serial ports (5V / 12V, 1x switchable to RS422 / RS485) [1]
  covered with black plastic caps
  SD card reader (supports SD, SDHC, SDXC)
  Power button
  Power LED (blue)
  HDD LED (yellow)
• Back Panel connectors
  DisplayPort 1.2 [2,7]
  2x HDMI 1.4b
  2x USB 2.0
  2x Intel Gigabit LAN (RJ45)
  Microphone input
  Audio Line-out (headphones)
  DC-input connector for external power adapter
  4-pin connector “SW2” (2.54 mm pitch) for power button, Clear CMOS and 5 V DC [4]
• Always-On Jumper
  By removing Jumper J9 (please refer to the quick user guide)
  the system will start unconditionally once power is applied. [6]
• Scope of Delivery
  Multi-language user guide
  Two metal feet with four screws M3 x 7
  VESA mount for 75/100mm standard (two metal brackets)
  Four thumbscrews M3 x 5 mm (screws together VESA mount and PC)
  Four screws M4 x 10 mm (to fix the VESA mount to the external surface)
  Rack (to mount a 2.5″ storage in the bay) with two screws M3 x 4 mm
  Driver DVD for Windows 10 (64-bit)
  External power adapter with power cord
• Environmental Specifications
  Operating temperature range: 0~40 °C [5]
  Relative humidity, non-condensing: 10~90 %
• Conformity & Certifications
  EMI: FCC, CE, BSMI, C-Tick
  Safety: ETL, CB, BSMI
  Other: RoHS, Energy Star, ErP
  This device is classed as a technical information equipment (ITE) in class B and is intended for use in living room and office. The CE-mark approves the conformity by the EU directives:
  (1) 2004/108/EC relating to electromagnetic compatibility (EMC),
  (2) 2006/95/EC relating to Electrical Equipment designed for use within certain voltage limits (LVD),
  (3) 2009/125/EC relating to ecodesign requirements for energy-related products (ErP),
  (4) 1999/5/EC related to Radio and Telecommunications Terminal Equipment (R&TTE)

Footnote:

[1] Jumper for COM port configuration
Pin 9 of the COM-Port is a multi-functional signal. Based on the Jumper JP1 configuration on the mainboard, it can be configured as Ring Indicator (RI) or external power supply with a voltage level of either 5 V or 12 V. Each COM port can be configured separately.
The operating mode of COM 1 can be set to RS232, RS422 or RS485 in the BIOS. COM 2 supports RS232 mode only.
[2] Note: the DisplayPort of DS77U3 does not support audio output.
[3] Teaming Mode
The teaming function allows you to group both available network adapters together to function as a single adapter. The benefit of this approach is that it enables load balancing and failover.
Driver download: https://downloadcenter.intel.com/download/21642
[4] Four-pin header at the back panel
This header allows for connecting an external power button.
It also provides 5 V DC voltage for external devices and the Clear CMOS function.
[5] Caution: for high ambient temperatures higher than 35 °C we strongly recommend to use an SSD instead of an HDD
[6] Power on after power fail:
The BIOS setup provides a “Power-On after Power Fail” function that can be found under “Power Management Configuration”. This function determines the PC’s behaviour after power failure. As a matter of the nature of this function, it may fail after short power failures. This is why the Shuttle XPC slim Barebone DS77U3 also comes with a hardware-based solution. By removing Jumper J9 (please refer to the quick user guide) the system will start unconditionally once power is applied.
[7] How to convert DisplayPort into HDMI/DVI
The DisplayPort output can be converted to HDMI or DVI by an additional, passive adapter cable. For example:
DELOCK 82590: 1 m, DisplayPort (male, 20p) to HDMI-A (male, 19p)
DELOCK 82435: 5 m, DisplayPort (male, 20p) to DVI-D (male, 24p)
The integrated graphics automatically detects the connected display and puts out the appropriate electric signal – either DisplayPort (without an adapter) or HDMI/DVI (with an adapter).
However, a monitor with a DisplayPort connector cannot be connected to the HDMI port with a simple, passive adapter.